Engine Oil – What It Does & How To Choose

What does my oil actually do?An engine oil's job is primarily to stop all the metal surfaces in your engine from grinding together and tearing themselves apart (and that's the last thing we'd want!). But it also has to dissipate the heat generated from this friction too. It also transfers heat away from the combustion cycle. Another function is that a good engine oil must be able to hold in suspension the nasty by-products of fuel combustion, such as silica (silicon oxide) and acids, whilst also cleaning the engine of such nasties. And it must do all of these things under tremendous heat and pressure without succumbing to fatigue.

Mineral or synthetic?Mineral oils are based on oil that comes from dear old Mother Earth which has been refined. Synthetic oils are entirely concocted by chemists wearing white lab coats in oil company laboratories. For more info, see the section on synthetics further down the page. The only other type is semi-synthetic, sometimes called premium, which is a blend of the two. It is safe to mix the different types, but it's wiser to switch completely to a new type rather than mixing.

A couple of words of warning:

If you've been driving around with mineral oil in your engine for years, don't switch to synthetic oil without preparation. Synthetic oils have been known to dislodge the baked-on deposits from mineral oils and leave them floating around your engine. It's wise to use a flushing oil first.

If you do decide to change, only go up the scale. If you've been running around on synthetic, don't change down to a mineral-based oil - your engine might not be able to cope with the degradation in lubrication. Consequently, if you've been using mineral oil, try a semi or a fully synthetic oil. By degradation, we’re referring to the wear tolerances that an engine develops based on the oil that it's using. Thicker mineral oils mean thicker layers of oil coating the moving parts (by microns though). Switching to a thinner synthetic oil can cause piston rings to leak and in some very rare cases, piston slap or crank vibration.
Gaskets and seals! With the makeup of synthetic oils being different from mineral oils, mineral-oil-soaked gaskets and seals have been known to leak when exposed to synthetic oils. Perhaps not that common an occurrence, but worth bearing in mind nevertheless.

SyntheticsDespite their name, most synthetic derived motor oils are actually derived from mineral oils - they are mostly Polyalphaolifins and these come from the purest part of the mineral oil refraction process, the gas. PAO oils will mix with normal mineral oil which means Joe public can add synthetic to his mineral, or mineral to his synthetic without his car engine seizing up. The most stable bases are polyol-ester (not polyester). What we meant by 'stable' is 'less likely to react adversely with other compounds.' Synthetic oil bases tend not to contain reactive carbon atoms for this reason. Reactive carbon has a tendency to combine with oxygen creating an acid. As you can imagine, in an oil, this would be A Bad Thing. So think of synthetic oils as custom-built oils. They're designed to do the job efficiently but without any of the excess baggage that can accompany mineral based oils.

Pure syntheticsPure synthetic oils (polyalkyleneglycol) are the types used almost exclusively within the industrial sector in polyglycol gearbox oils for heavily loaded gearboxes. These are typically concocted by intelligent blokes in white lab coats. These chaps break apart the molecules that make up a variety of substances, like vegetable and animal oils, and then recombine the individual atoms that make up those molecules to build new, synthetic molecules. This process allows the chemists to actually "fine tune" the molecules as they build them. Clever stuff. But Polyglycols don't mix with normal mineral oils.



A quick guide to the different grades of oil.


Fully Synthetic
Characteristics 0W-300W-405W-40
Fuel economy savings

Enhances engine performance and power

Ensures engine is protected from wear and deposit build-up

Ensures good cold starting and quick circulation in freezing temperatures

Gets to moving parts of the engine quickly


Semi-synthetic
Characteristics 5W-3010W-4015W-40
Better protection

Good protection within the first 10 minutes after starting out

Roughly three times better at reducing engine wear

Increased oil change intervals - don't need to change it quite so often


Mineral
Characteristics 10W-4015W-40
Basic protection for a variety of engines


Oil needs to be changed more often

So what should I buy?

Quality Counts! It doesn't matter what sort of fancy marketing goes into an engine oil, it's what's written on the packaging which counts. Specifications and approvals are everything. There are two established testing bodies. The API (American Petroleum Institute), and the European counterpart, the ACEA (Association des Constructeurs Europeens d'Automobiles - which was the CCMC). The API

The API classifications are different for petrol and diesel engines:
For petrol, listings start with 'S' (meaning Service category, but you can also think of it as Spark-plug ignition), followed by another code to denote standard. 'SM' is the current top grade, which recently replaced 'SL' and 'SH'. 'SH' will be found on most expensive oils, and almost all the new synthetics. It's basically an upgraded 'SG' oil which has been tested more sternly.

For diesel oils, the first letter is 'C' (meaning Commercial category, but you can also think of it as Compression ignition). 'CH' is the highest grade at the moment, (technically CH-4 for heavy-duty) but 'CF' is the most popular and is well adequate for passenger vehicle applications.

The ACEA standards are prefixed with a 'G' for petrol engines and a 'D' or 'PD' for diesel. Coupled with this are numerous approvals by car manufacturers which many oil containers sport with pride. ACEA replaced CCMC in 1996 primarily to allow for greater read-across in test programs (eg. for viscosity, viscosity modifiers and base oil). The CCMC specifications were G (1 to 5) for gasoline, D (1 to 5) or heavy duty diesel and PD1 and PD2 for passenger car diesel. ACEA though have a slightly different nomenclature they can be summarised as A for petrol, B for passenger car diesel and E for heavy duty diesel. The ACEA grades may also be followed by the year of issue which will be either '96, '98 (current) but coming soon is 2000.

Full ACEA specs are:
- A1 Fuel Economy Petrol
- A2 Standard performance level
- A3 High performance and / or extended drain
- B1 Fuel Economy diesel
- B2 Standard performance level
- B3 High performance and / or extended drain
- B4 For direct injection passenger car diesel engines
- E1 Non-turbo charged light duty diesel
- E2 Standard performance level
- E3 High performance extended drain
- E4 Higher performance and longer extended drain
- E5 (1999) High performance / long drain plus American/API performances. - This is ACEAs first attempt at a global spec.
Typically, these markings will be found in a statement similar to: Meets the requirements of API SH/CD along the label somewhere. Also, you ought to be able to see the API Service Symbol somewhere on the packaging:

If this is all confusing you, then rest assured that all top oils safely conform to the current standards. What you should treat with caution are the real cheapies and those with nothing but a maker's name on the pack. Cheap oil doesn’t mean it’s good!

SAE Grade counts too! The API/ACEA ratings only refer to an oil's quality. For grade, you need to look at the SAE (Society of Automotive Engineers) ratings. These describe the oil's function and viscosity standard. Viscosity means the substance and clinging properties of the lubricant. When cold, oil can become like treacle so it is important that any lube is kept as thin as possible. It's cold performance is denoted by the letter 'W', meaning 'winter'. At the other end of the scale, a scorching hot oil can be as thin as water and about as useful too. So it needs to be as thick as possible when warm. Thin when cold but thick when warm? That's where MultiGrade oil comes in. For ages, good old 20W/50 was the oil to have. But as engines progressed and tolerances decreased, a lighter, thinner oil was required, especially when cold. Thus 15W/50, 15W/40 and even 15W/30 oils are now commonplace. Synthetics can go down as far as 5W which seemed unbeatable until some brands came up with a 0W30 formulation! 'Free flowing' just doesn't describe it! It's predominantly a workshop oil but recommended for use in places like Canada in the winter. So again: what should I buy? That all depends on your car, your pocket and how you intend to drive and service the car. All brands claim theirs offers the best protection available - until they launch a superior alternative. It's like washing powders - whiter than white until new Super-Nukem-Dazzo comes out. For most motorists and most cars, a quality mainline oil is the best. Ones which are known to be good at their job and accepted by the general public. Go up a step again and you're looking at synthetic oils aimed squarely at the performance market. These are the ones which provide better endurance and favorable oil pressures for the demanding drivers.